Daily use and maintenance of LED advertising vehicles
Time:2019-08-13
Views:1617
LED car use and maintenance:
First, the advertising campaign should do the following work before moving long distance:
1. Check that the doors of the LED screen box are all locked.
2. Check if the LED screen has all been lowered.
3. Check for cracks in the welded joints of the LED screen plate steel plate and the steel plate lifting lugs.
4. Check the screws on the hub for looseness.
5. Check if the air pressure of the tire is normal.
Second, it is best to hang on the front end of the chassis steel plate when pulling. The distance between the tail end of the tractor and the front end of the media car is more than 1 meter. Otherwise, when the tractor turns, the tail of the tractor will damage the outer casing of the advertising vehicle. It is particularly noteworthy that the traction rods installed on the advertising vehicle are used for short-distance manual movement, and the tractor traction rods are absolutely not allowed.
Third, during the traction process, the speed of the vehicle is controlled at 30 kilometers per hour. The car dealers should always monitor the media car‘s every move, encounter uneven roads, and remind drivers to slow down.
4. After the advertising vehicle arrives at the designated location, first put down the four supporting feet and adjust the extension length (if the wind is big, the support feet are extended more) and the ground is tight.
5. If the wind exceeds 5, the screen cannot be raised to prevent the advertising vehicle from being scraped.
6. After the screen is raised, personnel should not put their heads into the gap between the bottom of the screen and the chassis to avoid accidents.
7. If the maintenance personnel need to perform maintenance after the screen is raised, the support frame for preventing sudden drop must be placed in the elevator.
8. Connect the grounding wire before starting the machine to prevent leakage.
Nine, the LED screen must be professionally repaired, the total power should be turned off during maintenance.
10. If there is a typhoon, it is best to park the advertising car indoors. It is best to use a rope to fix the advertising vehicle.
XI, advertising equipment LED equipment maintenance and precautions
1. After the advertising vehicle is used, it is best to park it indoors. This can effectively avoid the wind and the sun. When it is parked outdoors, it will be covered with the car cover after maintenance. The equipment should be used for at least 15 hours for at least 15 days. If the vehicle cover is closed for a long time, the circuit board of the LED module will regain moisture, resulting in short circuit of the circuit board.
2. The surface of the advertising car body is scrubbed with polishing wax for 7-15 days. The lift part is cleaned with a fine brush and cleaned with polishing wax. The tire can be scrubbed with a professional tire polish (not careful with corrosive Wash the lotion), clean the surface of the screen with a fine brush for 15 days (be careful not to wash it with a water pipe), and clean the internal space of the screen for 2 months.
3. After long-term use, the support legs, the traction part, the steel plate and the front and rear bridges are found to have rust. You can use sandpaper to clean and then apply black anti-rust paint. When the anti-rust paint is completely dry, brush the oil again. To keep the parts flexible.
4. The hydraulic oil of the lift is replaced once in one year, and the oil pipe is replaced once in 18 months.
5, the front and rear axle bearings are inspected once a year, the bearing is damaged and replaced with a new one, and then poured into the car‘s general lithium. If the tire pressure is insufficient, the air pressure should be adjusted to 6.5±0.5.
6. Check all the wires once a month, mainly check whether the line is broken or broken.
7. After each use of the equipment, all screws must be inspected and tightened - including (hub screws, steel plate screws, steel plate lug screws, led screen box screws, fan fixing screws).
First, the advertising campaign should do the following work before moving long distance:
1. Check that the doors of the LED screen box are all locked.
2. Check if the LED screen has all been lowered.
3. Check for cracks in the welded joints of the LED screen plate steel plate and the steel plate lifting lugs.
4. Check the screws on the hub for looseness.
5. Check if the air pressure of the tire is normal.
Second, it is best to hang on the front end of the chassis steel plate when pulling. The distance between the tail end of the tractor and the front end of the media car is more than 1 meter. Otherwise, when the tractor turns, the tail of the tractor will damage the outer casing of the advertising vehicle. It is particularly noteworthy that the traction rods installed on the advertising vehicle are used for short-distance manual movement, and the tractor traction rods are absolutely not allowed.
Third, during the traction process, the speed of the vehicle is controlled at 30 kilometers per hour. The car dealers should always monitor the media car‘s every move, encounter uneven roads, and remind drivers to slow down.
4. After the advertising vehicle arrives at the designated location, first put down the four supporting feet and adjust the extension length (if the wind is big, the support feet are extended more) and the ground is tight.
5. If the wind exceeds 5, the screen cannot be raised to prevent the advertising vehicle from being scraped.
6. After the screen is raised, personnel should not put their heads into the gap between the bottom of the screen and the chassis to avoid accidents.
7. If the maintenance personnel need to perform maintenance after the screen is raised, the support frame for preventing sudden drop must be placed in the elevator.
8. Connect the grounding wire before starting the machine to prevent leakage.
Nine, the LED screen must be professionally repaired, the total power should be turned off during maintenance.
10. If there is a typhoon, it is best to park the advertising car indoors. It is best to use a rope to fix the advertising vehicle.
XI, advertising equipment LED equipment maintenance and precautions
1. After the advertising vehicle is used, it is best to park it indoors. This can effectively avoid the wind and the sun. When it is parked outdoors, it will be covered with the car cover after maintenance. The equipment should be used for at least 15 hours for at least 15 days. If the vehicle cover is closed for a long time, the circuit board of the LED module will regain moisture, resulting in short circuit of the circuit board.
2. The surface of the advertising car body is scrubbed with polishing wax for 7-15 days. The lift part is cleaned with a fine brush and cleaned with polishing wax. The tire can be scrubbed with a professional tire polish (not careful with corrosive Wash the lotion), clean the surface of the screen with a fine brush for 15 days (be careful not to wash it with a water pipe), and clean the internal space of the screen for 2 months.
3. After long-term use, the support legs, the traction part, the steel plate and the front and rear bridges are found to have rust. You can use sandpaper to clean and then apply black anti-rust paint. When the anti-rust paint is completely dry, brush the oil again. To keep the parts flexible.
4. The hydraulic oil of the lift is replaced once in one year, and the oil pipe is replaced once in 18 months.
5, the front and rear axle bearings are inspected once a year, the bearing is damaged and replaced with a new one, and then poured into the car‘s general lithium. If the tire pressure is insufficient, the air pressure should be adjusted to 6.5±0.5.
6. Check all the wires once a month, mainly check whether the line is broken or broken.
7. After each use of the equipment, all screws must be inspected and tightened - including (hub screws, steel plate screws, steel plate lug screws, led screen box screws, fan fixing screws).
.png)
.png)
Mailme
18672222184